Відео

Question, I just got a 2016 maverick 1000 x ds and when I let off the gas or when going down hill it doesn't really coast. it sounds and acts more like when you downshift on a dirt bike. Is this normal?

Are the maintenance procedures for all the Massey GC subcontract tractors the same? I know you are doing an example using a 1700, but I have a 2410. Appreciate the video, a couple of really easy, simple things to do to keep your tractor running smoothly.

Part number please

control you're talking about that raises the 3-point hitch in the back it only controls it going down not up which I wished it did because I use my box scraper quite a bit and it's really aggravating not being able to slow it down and going up you always end up raising it too high and then you got to let it down how about the same tractor last year and a few other points that you missed quoted but if they read the owners manual they'll find out what they do that's the best way to go anyhow

Where’s the oil drain plug on a 1726e? What type of oil do we need?

Would have been nice to have the 3point lift leaver be up higher. Second wish the pto engagement wouldnt slam into using it could have made it engage better

It's not "three wheel drive" with the rear differential open. It's four wheel drive with open differentials. The front differential does not lock.

What about in fall when you wanna start it up again

Thank you.

The amount of space between the backhoe and the tractor is ridiculous! On a regular TLB the stabilizers are just a few inches away from the back tires. Any more than that is wasted space, and all that wasted space is just for the seat. But that space makes the tractor very tail heavy! I would never waste my money on a backhoe attachment!!!

What 2 keys?

I adjusted the cable. I checked the Throttle body . Looks perfectly fine. No ice in the Throttle. Still does it. I literally parked it for 45 mins to eat dinner then this is exactly what's going on now. Thinking could be a dess key issue? Could be a bad plug possibly (doubt it) could be a computer issue? Maybe a bad sensor? Like I was. Was running PERFECT an hour before this happened. Any help?

En español

Ancient artifact... but still useful Mike! :)

My POS 1725M is less than two months old and the fuel gage quit working. Indonesian tractor not love you long time.

My 1825 is two months old and I have to jiggle the neutral lever forward to get it to start. It also cuts off while the switch shows neutral and the parking brake is on. I have no idea how to adjust that neutral lever.

Thank you, my friend husband, passed away, we needed to figure out how to drive it properly, thank you, this was the best video.

Thank you. I just purchased a 2850 and I would like to remove the front end loader sometime soon.

Thanks for a quick accurate explanation. Others give a 10 minute talk about BS no one wants to hear and then they don't even give an accurate explanation like having the odometer setting on the sled. This was the third direction I listened to and the only one who said it straight and to the point.

Nice video. On the new 1723e does pto free spin when disengaged for a brush cutter or do you need a add on on the shaft so it doesn't stop when disengaged?

Great video! Does the hand knob below the seal that controls the speed up/down of the three point also control the speed of the belly mower coming up and down?

If I look down hydro hole should I see oil or not?

Stranded for over an hour after a roll over. This tip saved us big time! Able to ride back out like nothing happened. THANK YOU!

If I look down the hydro plug . Should I see hydro fluid?

Somebody needs to brief this kid on how sales videos work. 1- this is not a knowledge test for you. Don't run through it so fast. You're trying to convey information to the customer, not demonstrate your knowledge. 2- Sell the benefits, not the features. Most people don't care HOW it works. They just want to know WHAT IT DOES.

You Rule!

How big of a trailer we need to haul it

Does the 1736 have a DPF filter that can be replaced??

Any idea on 7622 MF that started not cranking until @6 key turns. Now it will not crank. 50 key turns at least. (Last month @3-5 key turns start right up). No power drain at all

Thank you, because I can't find my manual. I have a squirrel's brain.

How many hours can u get out of one of these tractors?

I have a GC2410 and I'm heading into this. I sure wish you used better audio recording on your video. Monaural mushy sound is so sixties.

It should be specified that this is a hydrostatic as the mechanical does not have that hydraulic filter. It’s has the hydraulic suction filter only.

Tractor 🚜 Mike!

Works like a charm, first time

May seem like it took a while, but 5 minutes shouldn’t make or break your day. Also better to do things slower and not risk breaking anything.

Mine is all good but can’t move and my throttle cable adjusted.

Why don’t you show how to put the tractor into either hair drive or rabbit drive. No instruction on how to put the vehicle in gear that’s sad

You didn't talk about when the pressure on the backhoe hydraulic lines are to strong to budge.

Do you need to lift the back end for the summer??

Hi I'm tiring to put a snow / grade blade on my three point on the MF 1739E. I have the backhoe removed. The brackets of course stay. I can't find a place to hook my stabilizers. Do you think they sacrificed my connection points for the backhoe brackets ? Where should I hook them?

Hi I'm tiring to put a snow / grade blade on my three point on the MF 1739E with backhoe . I have the backhoe removed. The brackets of course stay. I can't find a place to hook my stabilizers for the three point implement. Do you think they sacrificed my stabilizers connection points for the backhoe brackets ? Where should I hook them? Thanks

That was a fantastic overview. Thank you!

I want this tractor How much cost

Exilent work

Oh wow nice i wanaa one in india ❤️ love from india

اريد واحدة بالاقساط 🙄

Well done vid, but you skipped over the very first step: UNlatching the stands. I don't know about others, but my stands are latched up into the arm...good thing, you don't want them dropping down unexpectedly. However, for those who've never dropped the stands it's a little bit of a puzzle.

What if mines doing that and its 75 and sunny lol

Thanks! Easy enough!